1
/
of
4
Dupengda
Skeleton Saber
Skeleton Saber
1 review
Regular price
$232.50 USD
Regular price
$269.00 USD
Sale price
$232.50 USD
Unit price
/
per
Shipping calculated at checkout.
Couldn't load pickup availability
Share
RGB vs XENOPIXEL
RGB vs XENOPIXEL
| Function | RGB Upgrade | XENO Pixel 3.0 |
| Sound effects | 16 sets | 27sets/34 sets |
| Color change | 16 kinds + infinitely variable colors | 16 kinds + infinitely variable colors |
| Light effects | 3 kinds | 8 kinds |
| Power on animation | 3 kinds (two of them can be turned on by default off) | 12 kinds (5 of them can be turned on by default off) |
| Specific switch mode | Rotary switch, push-pull switch, swing switch, button | Rotary switch, push-pull switch, swing switch, push button |
| Battery capacity/specification | 3000mA | 3600mA |
| Blade specification | 82/92cm, 2mm wall thickness | 82/92cm, 2mm wall thickness |
| Blade mode | Normal light / micro-flash / burst flash | Stable light effect, pulse light effect, rainbow light effect, candy light effect, unstable mode, crack blade, flamer mode, flash mode |
| SD card | Yes | Yes |
| DIY | Support(New sound/parameter adjustment, etc.) | Support cell phone control(New sound effects/parameter adjustment, etc.) |
| Blade material | PC | PC |
| Packing list | Instruction manual, charging cable (without charging head), tools Bag, blade, handle | Instruction manual, charging cable (without charging head), tool kit, blade, handle, card reader, sword frame, sword sieve |
Method of use
Method of use
| When Saber Blade is on | When Saber Blade Is Off | ||
| Control | Effect | Control | Effect |
| Hold button and clash hilt | Lock UP | Button LED flash one time (Hold button 0.5 seconds) |
Adjust Volume |
| Button LED flash one time (Hold button 0.5 seconds) |
Drag | Button LED flash two times (Hold button 1 second) |
Change Light Effect |
| Button LED flash two times (Hold button 1 second) |
Infinite Color Change | Button LED flash three times (Hold button 1.5 seconds) |
Change Blade Mode |
| Button LED flash three times (Hold button 1.5 seconds) |
Turn Off Saber | Button LED flash four times (Hold button 2 seconds) |
Change to last Font |
| Point down hilt, hold the button and twist (Counterclockwise and then clockwise) |
Standard Color Change | Point down the hilt and twist Counterclockwise and then clockwise) |
Change to Next Font |
| Point down hilt, hold the button and twist (Clockwise and then counterclockwise) |
Twist Color Change | point up hilt and twist (counterclockwise and then clockwise) |
Play Music |
| point up the hilt, hold button and twist (Clockwise and then counterclockwise) |
Force Effect | ||
| Click button | Blaster/Blaster Deflect | ||
| Thrust the hilt forward | Stab | ||
| spin the hilt quickly | Spin | ||
| Hold button, and stab hilt (Twist to change melt color) |
Melt | ||
| Hold button and pull hilt inwards | Lightning Block | ||
| Enter into LOCK UP first, Then button LED flash one time (Hold button 0.5 second) |
Multi Lock Mode | ||
| hold button and swing saber (Same control to exit mode) |
Multi Block Mode | ||
| Hold button 10 seconds (After saber blade is off) |
Deep Sleep/Deactivate Saber | ||
| Hold button 10 seconds (When saber blade is off) |
Pixel to RGB/RGB to Pixel | ||
Troubleshooting
Troubleshooting
① saber still doesn't start after charging？
Remove the battery and check the battery contact
plates, to ensure they are making contact. Gently bend
them out if they are not making contact, reinsert the
battery, and turn on the saber if there is no response
charge again. (if possible, use an external charger).
② Saber has no swing, hum, or clash sounds?
Usually, this is from low battery power. Charge the saber
for. hours. In Xeno, ensure files are set up on the micro SD
card, and ensure the micro SD card is seated properly
③ Saber stops working suddenly?
Remove the battery and check the contact plates.
Reinsert the battery, charge the saber, and try again. lf
If there is no response, contact your seller.
Saber is hot near the emitter?
it is normal for the LED in the emitter to generate heat.
but the emitter should diffuse most of the heat. As such
please do not turn on the electronics outside of a hill, as
the heat may damage the chassis without the aluminum
emitter to diffuse the heat.
Remove the battery and check the battery contact
plates, to ensure they are making contact. Gently bend
them out if they are not making contact, reinsert the
battery, and turn on the saber if there is no response
charge again. (if possible, use an external charger).
② Saber has no swing, hum, or clash sounds?
Usually, this is from low battery power. Charge the saber
for. hours. In Xeno, ensure files are set up on the micro SD
card, and ensure the micro SD card is seated properly
③ Saber stops working suddenly?
Remove the battery and check the contact plates.
Reinsert the battery, charge the saber, and try again. lf
If there is no response, contact your seller.
Saber is hot near the emitter?
it is normal for the LED in the emitter to generate heat.
but the emitter should diffuse most of the heat. As such
please do not turn on the electronics outside of a hill, as
the heat may damage the chassis without the aluminum
emitter to diffuse the heat.
Light up your world with Skeleton lightsaber's rechargeable metal hilt. Take your cosplay, conventions, and parties to the next level with this ultra-realistic and customizable weapon. With an ergonomic design and durable material, you can trust that it will last for many battles to come. Let your inner Jedi shine and become a master of the force with our rechargeable metal hilt!
b
brian Nett I am very happy with this purchase, because it was delivered to me early than I thought. Though, the saber was not fully charged, so I guess I have to fully charge before using I think? Either way, the looks of it is very amazing and detailed just like in the Star Wars movie.
